Hear from Our Customers
When your breaker trips for the third time today, you’re not wondering if it’s serious. You already know it is. You’re wondering who’ll show up, how much it’ll cost, and whether they’ll actually fix it or just reset the breaker and leave.
Here’s what happens when you call a local electrical company in McCook that’s been doing this for 25 years: You get someone who understands that most homes here were built in 1961. That means outdated panels, insufficient amperage for modern appliances, and wiring that wasn’t designed for your EV charger or smart home setup. We don’t just patch the problem—we tell you what’s actually going on and what it’ll take to fix it for good.
You’re not left guessing. You get a licensed, bonded, and insured electrical contractor who shows up when they say they will, gives you a straight answer about what’s wrong, and gets your power back on without the runaround.
We’ve been the electrical company McCook homeowners call when things go sideways—usually at the worst possible time. Burning smell from the panel. Flickering lights that won’t stop. Power out in half the house and no idea why.
We’re licensed, bonded, and insured, which matters more than it sounds like it does. It means you’re covered if something goes wrong, and it means we’re held to a standard. We’ve spent 25 years learning how homes in McCook are wired, what fails first, and how to fix it so it doesn’t fail again next month.
We’re not the cheapest option, and we’re fine with that. You’re paying for someone who knows the difference between a quick fix and a real one—and who’ll tell you which one you actually need.
You call or text, and we pick up. If it’s an emergency—burning smell, sparking outlet, total power loss—we’re available 24/7. If it’s not urgent, we schedule a time that works for you.
We show up on time. Our electrician walks through what’s happening, checks your panel, tests your circuits, and figures out what’s actually wrong. Not what might be wrong. What is wrong.
You get an upfront price before we do anything. No surprises, no “we’ll see when we get in there” nonsense. If you’re a senior, teacher, first responder, military, or student, you get a discount. If you’re a new customer, same thing.
We do the work. We test it. We clean up. And if something doesn’t feel right to you after we leave, you call us back. That’s it. That’s the whole process. No upselling, no pressure, no treating you like you don’t understand your own house.
Ready to get started?
Most of what we do falls into a few categories: emergency repairs, panel upgrades, circuit work, and EV charger installations. The emergency stuff is usually straightforward—power’s out, something’s sparking, or there’s a burning smell. We find the problem, fix it, and make sure it’s safe.
Panel upgrades are bigger but necessary, especially in McCook where the median home was built in 1961. Those old panels weren’t designed for modern electrical loads. If your breaker keeps tripping or you’re adding central air, a heat pump, or an EV charger, your panel probably can’t handle it. We’ll tell you if you need an upgrade or if your current setup can manage.
Circuit work covers adding new circuits for appliances, fixing outlets that don’t work, and troubleshooting why half your house loses power when you run the microwave. It’s not glamorous, but it’s the kind of thing that makes your house livable again.
EV charger installation is becoming more common. You need a dedicated 240-volt circuit, and most older homes don’t have the capacity without a panel upgrade. We’ll assess what you’ve got and tell you what it’ll take to charge your car at home without blowing a fuse every time.
If your home was built in the 1960s—like most in McCook—and you’ve never upgraded your panel, there’s a good chance it’s undersized for what you’re asking it to do now. Panels from that era were typically 60 to 100 amps, which was fine when homes had fewer appliances and no central air.
Today, most homes need at least 200 amps to run modern HVAC systems, kitchen appliances, EV chargers, and electronics without constantly tripping breakers. If you’re flipping breakers regularly, planning to add a major appliance, or noticing lights dim when the AC kicks on, your panel is likely maxed out.
We’ll check your current panel’s capacity, measure your actual electrical load, and tell you whether an upgrade makes sense now or if you can wait. It’s not always urgent, but it’s something you’ll eventually need to address if you want your electrical system to keep up with how you actually live.
Turn off the main breaker if you can do it safely, and call an emergency electrician immediately. A burning smell near your panel usually means something’s overheating—loose wiring, a failing breaker, or an overloaded circuit. None of those fix themselves, and all of them can start a fire.
Don’t wait to see if it goes away. Electrical fires often start small and inside walls where you can’t see them until it’s too late. If the smell is strong or you see smoke, get out of the house and call 911 first, then call us.
We’ve seen this plenty of times in McCook’s older homes. Panels that have been in service for 60+ years develop issues—connections loosen, breakers wear out, and wiring degrades. When we get a call about a burning smell, we treat it like the emergency it is. We’ll inspect the panel, identify the source, and either repair or replace what’s failing before it becomes a bigger problem.
It depends entirely on what’s wrong and what it takes to fix it. A simple repair—replacing a faulty outlet or resetting a tripped GFCI—might run $150 to $300. Panel upgrades typically range from $2,000 to $4,000 depending on the size and complexity. EV charger installations vary based on whether you need a panel upgrade or just a new circuit.
We give you a flat-rate price before we start any work, so you know exactly what you’re paying. No hourly surprises, no “we found something else” upsells unless it’s a genuine safety issue we didn’t know about until we opened the panel.
If you’re a senior, teacher, first responder, military member, student, or new customer, we offer discounts that can take a chunk off the final bill. The best way to know what your specific job will cost is to call us for an estimate. We’ll ask the right questions, and if we need to see it in person to give you an accurate number, we’ll schedule that.
Yes. Electrical emergencies don’t wait for business hours, and neither do we. If you’ve got a power outage, a sparking outlet, a burning smell, or anything else that feels dangerous, call us any time—day or night, weekends, holidays.
Emergency electrical work costs more than scheduled service because we’re dropping everything to get to you fast, but you’re paying for speed and safety when you need it most. We’ll stabilize the situation, make sure your home is safe, and get your power back on if possible.
Most emergency calls we get in McCook involve tripped breakers that won’t reset, sudden power loss to part of the house, or something that smells or sounds wrong near the panel. We’ve handled all of it, and we’ve been doing it for 25 years. When you call, you’re talking to someone who knows what questions to ask and what to bring to fix it the first time.
Yes. We’re fully licensed as an electrical contractor in Illinois, bonded, and insured. That’s not just a box we check—it’s protection for you and accountability for us.
Being licensed means we’ve met the state’s requirements for training, testing, and ongoing education. It means our work has to meet code, and if it doesn’t, we’re the ones on the hook. Being bonded means if we don’t finish a job or don’t do it right, there’s a financial safety net for you. Being insured means if something goes wrong—damage to your property, an injury on the job—you’re not liable.
A lot of people don’t ask about this until after they’ve hired someone, and that’s when they find out the person working in their panel isn’t actually licensed. If something goes wrong and they’re not insured, you’re stuck with the bill and the liability. We’ve been in business for 25 years because we do this the right way, and that starts with being properly licensed, bonded, and insured.
Yes, we install EV chargers, but the real question is whether your current electrical system can handle one. Most EV chargers need a dedicated 240-volt circuit with 40 to 50 amps, which is a significant load—about the same as running an electric dryer and an oven at the same time.
If your home was built in the 1960s and still has its original panel, there’s a good chance you don’t have the spare capacity for an EV charger without upgrading your panel first. We’ll assess your current setup, measure your available capacity, and tell you whether you need a panel upgrade or if we can add the circuit with what you’ve got.
The installation itself involves running a new circuit from your panel to your garage or driveway, installing a dedicated breaker, and mounting the charger. We handle the permit and inspection if required. Once it’s done, you’ll be able to charge your car overnight without worrying about tripping breakers or overloading your system. We’ll walk you through the whole process and give you a clear price before we start.
Local Resources
